MAX485 TTL to RS-485 Interface Module — Half-Duplex, Modbus RTU, Arduino
MAX485 TTL to RS-485 Interface Module Half-Duplex, Modbus RTU, Arduino
Compatible JST cables for sensors and modules — secure & reliable. Shop now.
Couldn't load pickup availability
MAX485 TTL to RS-485 Interface Module — Half-Duplex, Modbus RTU, Arduino
The MAX485 module converts between TTL serial (UART) and RS-485 differential signals, enabling Arduino and other microcontrollers to communicate over RS-485 industrial networks at distances up to 1200m. RS-485 differential signaling provides excellent noise immunity in industrial environments, and the multi-drop bus topology supports up to 32 devices on a single twisted-pair cable. Compatible with Modbus RTU, DMX512, and other RS-485 protocols.
Electrical Specifications
- IC: Maxim MAX485
- Mode: Half-duplex (transmit or receive, not simultaneously)
- Data Rate: Up to 2.5Mbps
- Range: Up to 1200m (at lower baud rates)
- Bus Nodes: Up to 32 devices per bus segment
- Supply Voltage: 3.3V – 5V
- Control Pins: DE (Driver Enable) + RE (Receiver Enable)
- Signaling: Differential (A/B lines) — excellent noise immunity
Arduino Wiring
- VCC → 5V | GND → GND
- DI (Data In) → Arduino TX pin
- RO (Receiver Out) → Arduino RX pin
- DE + RE → Arduino digital pin (tie together, HIGH=transmit, LOW=receive)
- A/B → RS-485 bus twisted pair
- Add 120Ω termination resistor at each end of the bus
RS-485 vs UART vs I²C
- RS-485: 1200m range, 32 nodes, noise-immune differential — for industrial networks
- UART: ~15m range, point-to-point — for short-distance serial communication
- I²C: ~1m range, multi-device — for on-board sensor communication
Typical Applications
- Arduino Modbus RTU master/slave — communicate with industrial sensors, meters, and PLCs
- Building automation RS-485 bus — HVAC, lighting, and access control networks
- Energy monitoring — smart meter and power analyzer communication
- DMX512 lighting control — stage and architectural lighting
- Multi-node sensor network — up to 32 Arduino nodes on one cable
MAX485 half-duplex RS-485 module — 1200m range, 32 nodes, Modbus RTU compatible for Arduino industrial networking and long-distance serial communication.

Blog posts
View all-
Best JST Connector Crimping Tools in 2026: Engi...
Choosing the wrong crimping tool ruins JST connectors and wastes wire. This guide compares the top crimping tools for JST SH, GH, PH, XH, and VH series — including Engineer...
Best JST Connector Crimping Tools in 2026: Engi...
Choosing the wrong crimping tool ruins JST connectors and wastes wire. This guide compares the top crimping tools for JST SH, GH, PH, XH, and VH series — including Engineer...
-
Molex KK 254 vs Mini-Fit Jr. vs Micro-Fit 3.0: ...
Choosing between Molex KK 254, Mini-Fit Jr., and Micro-Fit 3.0? This guide compares pitch, current rating, locking mechanism, wire gauge, and typical applications — with decision tables, part number references,...
Molex KK 254 vs Mini-Fit Jr. vs Micro-Fit 3.0: ...
Choosing between Molex KK 254, Mini-Fit Jr., and Micro-Fit 3.0? This guide compares pitch, current rating, locking mechanism, wire gauge, and typical applications — with decision tables, part number references,...
-
DuPont Connector vs JST PH 2.0: Pinout, Specs &...
Not sure whether to use a DuPont 2.54mm or JST PH 2.0mm connector? This guide compares pitch, locking mechanism, current rating, pinout, and best use cases — so you can...
DuPont Connector vs JST PH 2.0: Pinout, Specs &...
Not sure whether to use a DuPont 2.54mm or JST PH 2.0mm connector? This guide compares pitch, locking mechanism, current rating, pinout, and best use cases — so you can...