JST, Molex, DuPont & Yeonho Connector Cables: The Complete Keszoox Guide to Every Series, Pitch & Application
Keszoox Connector Cable Assemblies: The Complete Reference
Keszoox supplies pre-crimped connector cable assemblies across four major connector families — JST, Molex, DuPont, and Yeonho — covering pitches from 1.0mm to 4.2mm and current ratings from 1A to 13A per contact. This guide is the single reference point for every connector series Keszoox stocks: what each series is, what it is used for, how it compares to alternatives, and where to find the complete individual guide for each one.
Whether you are an engineer selecting a connector for a new PCB design, a maker wiring an RC vehicle or 3D printer, or a procurement specialist sourcing pre-crimped harnesses for production, this page maps the entire Keszoox connector catalog to your application requirements.
How to Use This Guide
- Know your pitch? Jump to the pitch section below to find all connectors at that spacing.
- Know your brand/series? Use the brand sections (JST / Molex / DuPont / Yeonho) to navigate directly.
- Not sure what you have? See How to Measure Connector Pitch and How to Identify JST Connectors.
- Need to choose between WTB and WTW? See Wire-to-Board Connector Types.
Keszoox pre-crimped connector cable assemblies across 15+ series: JST XH, PH, ZH, SH, PA, XA, SM, Molex 51005, DuPont 2.54mm, and more. All assemblies use factory-crimped terminals and UL-rated wire. Available in 2–12 pin configurations with multiple wire exit orientations.
Quick Reference: All Keszoox Connector Series by Pitch
| Pitch | Series | Brand | Current | Type | Key Application |
|---|---|---|---|---|---|
| 1.0mm | JST SH | JST | 1A | WTB / WTW | Drones, flight controllers, compact sensors |
| 1.25mm | JST GH | JST | 1A | WTB / WTW | Pixhawk, autopilot, compact robotics |
| 1.25mm | Molex PicoBlade | Molex | 1A | WTB | Compact PCB, LiPo battery, wearables |
| 1.5mm | JST ZH | JST | 1A | WTB | Micro servo, compact consumer electronics |
| 2.0mm | JST PH | JST | 2A | WTB | LiPo battery, RC, Arduino sensors |
| 2.0mm | JST PA | JST | 3A | WTW | RC battery pigtails, wire-to-wire power |
| 2.0mm | JST SAN | JST | 3A | WTB | VTR, AV equipment, consumer electronics |
| 2.0mm | HY2.0 (Yeonho SMH200) | Yeonho | 3A | WTB | RC, 3D printers, drones, robotics |
| 2.0mm | PHB2.0 (Yeonho SMAW200) | Yeonho | 3A | WTB dual-row | High-density 2.0mm WTB, belt-lock |
| 2.0mm | JST PHD | JST | 2A | WTB dual-row | High-density PCB, compact dual-row WTB |
| 2.0mm | Molex 51005/51006 | Molex | 2A | WTB | RC, FPV, compact PCB wiring |
| 2.0mm | DuPont 2.0mm | Generic | 3A | WTB | Prototyping, consumer electronics |
| 2.5mm | JST XH | JST | 3A | WTB | RC balance leads, 3D printers, Arduino |
| 2.5mm | XHS2.5 (Yeonho SMH250 WTB) | Yeonho | 3A | WTB belt-lock | Industrial WTB, 3D printers, automation |
| 2.5mm | Yeonho SMH250 WTW (25045HP-NNA) | Yeonho | 3A | WTW retainer-lock | Vibration-resistant WTW, field harness |
| 2.5mm | JST XA | JST | 3A | WTB | Automotive, industrial, high-cycle WTB |
| 2.5mm | JST SCN | JST | 3A | WTB board-in | Board-in crimp, compact PCB |
| 2.5mm | JST SM | JST | 3A | WTW | LED strips, RC, general wire-to-wire |
| 2.5mm | JST EH | JST | 3A | WTB low-profile | Low-profile PCB, space-constrained WTB |
| 2.5mm | Molex Mini-SPOX | Molex | 3A | WTB / WTW | General 2.5mm WTB/WTW, automotive acc. |
| 2.5mm | JST RCY (SYP) | JST | 3A | WTW 2-pin | RC battery, LED power, 2-pin WTW |
| 2.54mm | DuPont 2.54mm | Generic | 3A | WTB | Arduino, breadboard, prototyping |
| 2.54mm | Molex KK 254 | Molex | 3A | WTB | PCB production wiring, industrial WTB |
| 2.54mm | Molex SL | Molex | 3A | WTB | PCB wiring, industrial, high-cycle |
| 3.0mm | Molex Micro-Fit 3.0 | Molex | 5A | WTB / WTW | Power distribution, server, industrial |
| 3.5mm | JST BHS | JST | 3A | WTB SMT / WTW | LCD backlight, high-voltage, SMT WTB |
| 3.96mm | JST VH | JST | 10A | WTB / WTW | Power supply, motor, high-current WTW |
| 4.2mm | Molex Mini-Fit Jr. | Molex | 13A | WTB / WTW | ATX power, server PSU, high-current |
JST Connector Cable Assemblies
JST connector cable assemblies from Keszoox in a typical flight controller application: JST SH 1.0mm and GH 1.25mm connectors wiring a stacked F405 flight controller to ESC, GPS, and telemetry modules. The inset shows pre-crimped JST cable assemblies in 6–16 pin configurations on blue background.
JST (Japan Solderless Terminal) is the world’s most widely referenced connector brand in the maker, RC, and embedded electronics communities. Keszoox stocks pre-crimped JST cable assemblies across 15 series, from the ultra-compact SH 1.0mm used in flight controllers to the high-current VH 3.96mm used in power distribution systems. All JST cable assemblies from Keszoox use UL-rated wire with factory-crimped terminals.
For a complete overview of the JST connector family, see our 12 Most Common JST Connector Types guide and JST Connector Models Explained.
JST SH 1.0mm — Ultra-Compact, 1A
The JST SH is the smallest connector in the Keszoox catalog at 1.0mm pitch. Rated at 1A / 50V, it is the standard connector for flight controllers (Betaflight, KISS, Pixhawk peripherals), compact sensor modules, and wearable electronics. The SH uses a friction-lock housing with no latch tab. → JST SH 1.0mm Complete Guide
JST GH 1.25mm — Pixhawk Standard, 1A
The JST GH at 1.25mm pitch is the official connector standard for Pixhawk autopilot systems (TELEM, GPS, I²C, CAN ports). Rated at 1A / 50V, it is also used in compact robotics, drone peripherals, and any application requiring a small, latched WTB connector. Mechanically similar to the Molex PicoBlade but not cross-compatible. → JST GH 1.25mm Complete Guide
JST ZH 1.5mm — Micro Servo Standard, 1A
The JST ZH at 1.5mm pitch is the standard connector for micro and nano servos. Rated at 1A / 50V. Also used in compact consumer electronics and camera modules. → JST ZH 1.5mm Complete Guide
JST PH 2.0mm — LiPo Battery Standard, 2A
The JST PH at 2.0mm pitch is the most widely used small connector in the RC and maker community — it is the standard connector for 1S–3S LiPo batteries, Arduino sensor modules, and Raspberry Pi accessories. Rated at 2A / 100V. → JST PH 2.0mm Complete Guide | PH vs SH Comparison
JST PA 2.0mm — Wire-to-Wire, 3A
The JST PA at 2.0mm pitch is the wire-to-wire variant in the 2.0mm space, rated at 3A — 50% higher current than the JST PH. Used for RC battery pigtails and power distribution harnesses. → JST PA 2.0mm Complete Guide
JST SAN 2.0mm — VTR / AV Equipment, 3A
The JST SAN at 2.0mm pitch is a wire-to-board connector used in VTR equipment, AV devices, and consumer electronics. Available in A-type and B-type terminal variants. → JST SAN 2.0mm Complete Guide
JST PHD 2.0mm — Dual-Row WTB, 2A
The JST PHD at 2.0mm pitch is the dual-row wire-to-board variant of the PH family, providing higher pin density in the same pitch. → JST PHD 2.0mm Complete Guide
JST XH 2.5mm — RC Balance Lead Standard, 3A
The JST XH at 2.5mm pitch is the standard connector for LiPo battery balance leads (2S–6S), 3D printer thermistor and endstop wiring, and general-purpose Arduino wiring. Rated at 3A / 250V. → JST XH 2.5mm Complete Guide
JST XA 2.5mm — Automotive-Grade WTB, 3A
The JST XA at 2.5mm pitch is the automotive and industrial-grade variant in the 2.5mm space, featuring a more robust housing and higher mating cycle rating than the XH. → JST XA 2.5mm Complete Guide
JST SCN 2.5mm — Board-In Crimp, 3A
The JST SCN at 2.5mm pitch is a board-in crimp connector where the terminal crimps directly onto the PCB edge, eliminating the need for a separate PCB header. → JST SCN 2.5mm Complete Guide
JST SM 2.5mm — Wire-to-Wire, 3A
The JST SM at 2.5mm pitch is the most common wire-to-wire connector in the 2.5mm space, widely used for LED strip connections, RC wiring, and general-purpose WTW applications. → JST SM 2.5mm Complete Guide
JST EH 2.5mm — Low-Profile WTB, 3A
The JST EH at 2.5mm pitch is a low-profile wire-to-board connector used in space-constrained PCB designs where vertical clearance is limited. → JST EH 2.5mm Complete Guide
JST RCY / SYP 2.5mm — 2-Pin WTW, 3A
The JST RCY (also known as JST SYP) is a dedicated 2-pin wire-to-wire connector at 2.5mm pitch, used for RC battery connections and LED power leads. → JST RCY / SYP Complete Guide
JST BHS 3.5mm — SMT WTB / High-Voltage, 3A
The JST BHS at 3.5mm pitch is an SMT wire-to-board connector with a high-voltage variant used for LCD backlight inverter wiring. → JST BHS 3.5mm Complete Guide
JST VH 3.96mm — High-Current WTB/WTW, 10A
The JST VH at 3.96mm pitch is the highest-current JST connector in the Keszoox catalog, rated at 10A / 250V. Used for motor wiring, power supply connections, and battery management systems. → JST VH 3.96mm Complete Guide | VH Model Numbers & Crimping Guide
🛒 Need JST cable assemblies? Browse our JST Connector Kit with 22AWG Pre-Crimped Cables — Assorted Series & Pin Counts — covers SH, GH, ZH, PH, XH, VH and more in one kit.
Molex Connector Cable Assemblies
Keszoox Molex-compatible connector families by pitch: PicoBlade 1.25mm, 51005/51006 2.0mm, Micro-Fit 3.0mm, Mini-Fit Jr. 4.2mm, SL 2.54mm, and DuPont 2.54mm. All with factory-crimped cable assemblies.
Molex is one of the world’s largest connector manufacturers. Keszoox stocks pre-crimped Molex-compatible cable assemblies across 7 key series. For a complete overview, see our Molex Connector Types Complete Guide and How to Identify Molex Connectors.
Molex PicoBlade 1.25mm — Ultra-Compact WTB, 1A
The Molex PicoBlade at 1.25mm pitch is Molex’s answer to the JST GH in the ultra-compact WTB space. Rated at 1A, used in compact PCB designs, LiPo battery connections, and wearable electronics. Mechanically similar to JST GH but not cross-compatible. → Molex PicoBlade 1.25mm Complete Guide
Molex 51005 / 51006 2.0mm — RC & FPV, 2A
The Molex 51005/51006 series at 2.0mm pitch is widely used in RC vehicles, FPV systems, and compact PCB wiring. Rated at 2A, a common alternative to the JST PH. → Molex 51005/51006 Complete Guide
Molex Mini-SPOX 2.5mm — General WTB/WTW, 3A
The Molex Mini-SPOX at 2.5mm pitch is a versatile connector available in both WTB and WTW configurations, rated at 3A. Used in automotive accessories and consumer electronics. → Molex Mini-SPOX 2.5mm Complete Guide
Molex KK 254 2.54mm — Production WTB, 3A
The Molex KK 254 at 2.54mm pitch is the industry-standard production wire-to-board connector, used in PCB production wiring and industrial equipment. → Molex KK 254 Complete Guide
Molex SL 2.54mm — Industrial WTB, 3A
The Molex SL at 2.54mm pitch is a high-cycle industrial wire-to-board connector used in industrial instrumentation and test equipment. → Molex SL 2.54mm Complete Guide
Molex Micro-Fit 3.0 — Power Distribution, 5A
The Molex Micro-Fit 3.0 at 3.0mm pitch is a dual-row power connector rated at 5A per contact, used in server power distribution and industrial power supplies. → Molex Micro-Fit 3.0 Complete Guide
Molex Mini-Fit Jr. 4.2mm — ATX Power Standard, 13A
The Molex Mini-Fit Jr. at 4.2mm pitch is the connector used in ATX power supplies and server PSUs. Rated at 13A per contact — the highest current rating in the Keszoox catalog. → Molex Mini-Fit Jr. 4.2mm Complete Guide
🛒 Need Molex cable assemblies? Browse our Molex Connector Kit — Male & Female Housings with Pre-Crimped Wires, Assorted Pitch.
DuPont Connector Cable Assemblies
Keszoox DuPont 2.54mm connector cable assemblies in a typical Arduino/PCB application: multi-color female DuPont crimp connectors wired to a motherboard GPIO header.
The “DuPont” connector is a generic, non-proprietary crimp connector family that has become the de facto standard for breadboard and Arduino wiring. Keszoox stocks two DuPont pitch variants:
DuPont 2.54mm — Arduino & Breadboard Standard, 3A
The DuPont 2.54mm connector at 2.54mm pitch is the universal standard for Arduino GPIO wiring, breadboard jumper cables, and prototyping harnesses. The no-latch friction-fit housing allows fast connect/disconnect during development. → DuPont 2.54mm Complete Guide
DuPont 2.0mm — Compact Prototyping, 3A
The DuPont 2.0mm connector at 2.0mm pitch provides a 21% smaller footprint than the 2.54mm standard while maintaining the same no-latch friction-fit design. Used in space-constrained prototyping and consumer device internal wiring. → DuPont 2.0mm Complete Guide
🛒 Need DuPont jumper cables? Browse our DuPont 2.54mm Male to Female Connector Kit — 22AWG Pre-Crimped, Assorted Pin Counts.
Yeonho Connector Cable Assemblies
Yeonho and JST connector cable assemblies in an FPV drone flight controller stack application: JST SH 1.0mm and Yeonho XHS2.5 2.5mm connectors wiring ESC and flight controller boards.
Yeonho Electronics is a South Korean connector manufacturer whose SMH200 and SMH250 series have become widely adopted in the RC, 3D printing, and industrial automation communities under the generic names HY2.0 and XHS2.5. Keszoox stocks Yeonho-compatible cable assemblies across four series:
HY2.0 — Yeonho SMH200, 3A (Wire-to-Board)
The HY2.0 connector (official designation: Yeonho SMH200 / 20037-HNN) at 2.0mm pitch is rated at 3A — 50% higher than the JST PH at the same pitch. It is the preferred choice over JST PH in higher-current RC, robotics, and 3D printer applications. → HY2.0 / Yeonho SMH200 Complete Guide
PHB2.0 — Yeonho SMAW200, 3A (Dual-Row WTB)
The PHB2.0 connector (official designation: Yeonho SMAW200) at 2.0mm pitch is the dual-row, belt-lock variant of the HY2.0 family, providing higher pin density with a positive locking mechanism. → PHB2.0 / Yeonho SMAW200 Complete Guide
XHS2.5 — Yeonho SMH250 Wire-to-Board, 3A
The XHS2.5 connector (official designation: Yeonho SMH250 WTB series) at 2.5mm pitch features a belt-lock latch for positive retention in wire-to-board applications. Used in industrial automation, 3D printers, and any 2.5mm WTB application requiring a more secure connection than the JST XH. → XHS2.5 / Yeonho SMH250 WTB Complete Guide
SMH250 Wire-to-Wire — Yeonho 25045HP-NNA, 3A
The Yeonho SMH250 wire-to-wire connector (plug housing: 25045HP-NNA) at 2.5mm pitch is the only connector in the Keszoox 2.5mm WTW lineup with a red secondary retainer lock, providing dual-stage terminal retention for vibration-resistant applications. Rated at 3A / 250V with a 1μsec MAX vibration discontinuity specification. → Yeonho SMH250 WTW Complete Guide
🛒 Need Yeonho cable assemblies? Browse our HY2.0 Connector Kit — 22AWG Pre-Crimped, Yeonho SMH200 · SMH250 2.5mm Connector Kit
How to Choose the Right Connector: Key Selection Criteria
Mating a wire-to-wire connector cable assembly by hand: the plug housing (left) is aligned with the socket housing (right) and pushed together until the latch engages. Proper connector selection — matching pitch, current rating, and locking mechanism to the application — ensures reliable long-term connection.
Step 1 — Determine connection type: Wire-to-Board (WTB) connects a cable to a PCB header. Wire-to-Wire (WTW) connects two cable assemblies. See our Wire-to-Board Connector Types guide for a full framework.
Step 2 — Measure or determine the pitch: Pitch is the center-to-center distance between adjacent contacts. See How to Measure Connector Pitch if you are identifying an unknown connector.
Step 3 — Verify current and voltage requirements: Match the connector’s rated current to your application’s maximum continuous current. Apply a minimum 20% derating for continuous-duty applications.
Step 4 — Check wire gauge compatibility: Each connector series has a specified wire gauge range. See How to Crimp JST Connectors for crimping guidance applicable across most series.
Step 5 — Consider locking requirements: No-latch (DuPont, JST SH) for frequent disconnection; friction latch (JST PH, XH) for standard retention; belt-lock (XHS2.5) or retainer lock (Yeonho 25045HP-NNA) for vibration environments.
Step 6 — Consider contact material: Tin-plated contacts for standard applications; gold-plated for high-cycle or low-contact-resistance requirements. See Brass vs Phosphor Bronze Connector Contacts for material selection guidance.
Why Keszoox for Connector Cable Assemblies?
- Factory-crimped terminals: Consistent crimp geometry and pull-force retention across all units — no manual crimping required for low-volume applications.
- UL-rated wire: All cable assemblies use UL1007 or UL1061 PVC insulation with rated voltage and temperature specifications.
- Multiple wire exit orientations: Reverse-side-head, same-side-head, single-head (pigtail), and male–female extension variants available across most series.
- RoHS compliant: All products comply with EU RoHS Directive 2011/65/EU.
- Global shipping: Ships worldwide from Keszoox’s fulfillment center.
- 28 connector series in stock: JST (15 series), Molex (7 series), DuPont (2 series), Yeonho (4 series) — the broadest connector cable catalog available from a single supplier.
Connector Knowledge Base
- How to Identify JST Connectors: Pitch, Series & Pin Count Guide
- How to Identify Molex Connectors: Series, Pitch & Application Guide
- How to Measure Connector Pitch: JST & Molex Identification Guide
- How to Crimp JST Connectors: Step-by-Step Guide for XH, PH & SH Series
- Wire-to-Board Connector Types: Complete Guide to Choosing the Right One
- Brass vs Phosphor Bronze Connector Contacts: Which Material Should You Choose?
- Active vs Passive Components: Key Differences Explained
- JST PH vs SH: Key Differences, Specs & Which to Choose
- Common JST Connector Types & Their Applications
Frequently Asked Questions
What connector cable brands does Keszoox supply?
Keszoox supplies pre-crimped connector cable assemblies compatible with four major connector families: JST (SH 1.0mm, GH 1.25mm, ZH 1.5mm, PH 2.0mm, PA 2.0mm, SAN 2.0mm, PHD 2.0mm, XH 2.5mm, XA 2.5mm, SCN 2.5mm, SM 2.5mm, EH 2.5mm, RCY 2.5mm, BHS 3.5mm, VH 3.96mm — 15 series), Molex (PicoBlade 1.25mm, 51005/51006 2.0mm, Mini-SPOX 2.5mm, KK 254 2.54mm, SL 2.54mm, Micro-Fit 3.0mm, Mini-Fit Jr. 4.2mm — 7 series), DuPont (2.54mm and 2.0mm), and Yeonho (HY2.0/SMH200 2.0mm, PHB2.0/SMAW200 2.0mm, XHS2.5/SMH250 WTB 2.5mm, SMH250 WTW/25045HP-NNA 2.5mm). All products use factory-crimped terminals and UL-rated wire.
What is the difference between JST and Molex connectors?
JST (Japan Solderless Terminal) and Molex are both major connector manufacturers, but their product lines serve different primary markets. JST connectors (SH, GH, PH, XH, VH) dominate the RC, drone, and maker electronics markets due to their compact pitch options and wide availability. Molex connectors (PicoBlade, KK 254, Mini-Fit Jr.) are more prevalent in industrial, automotive, and computer hardware applications. Both brands offer connectors at overlapping pitches (1.25mm, 2.5mm, 2.54mm) that are not cross-compatible despite similar dimensions.
What is the most common connector pitch for RC and maker electronics?
The most common connector pitches in RC and maker electronics are: 1.0mm (JST SH — flight controllers), 1.25mm (JST GH — Pixhawk; Molex PicoBlade), 2.0mm (JST PH — LiPo batteries; HY2.0 — RC/3D printers), and 2.5mm (JST XH — balance leads; XHS2.5 — industrial). The JST PH 2.0mm is the single most common connector in the 1S–3S LiPo battery ecosystem.
Are JST connectors and DuPont connectors interchangeable?
No. JST connectors and DuPont connectors are not interchangeable, even at the same pitch. The JST PH (2.0mm) and DuPont 2.0mm have different housing geometries, terminal designs, and mating interfaces. The DuPont 2.54mm and JST XH (2.5mm) are at different pitches and are not compatible. Always verify the exact series and pitch before ordering replacement connectors.
What wire gauge should I use with JST connectors?
Wire gauge depends on the connector series: JST SH and GH use AWG 28–32; JST ZH and PH use AWG 26–30; JST XH and VH use AWG 22–26. As a general rule, use the heaviest gauge within the connector’s specified range for power lines, and lighter gauges for signal lines. Keszoox pre-crimped assemblies use 22AWG for 2.5mm+ series and 26–28AWG for 1.0–1.5mm series.
What is the difference between wire-to-board and wire-to-wire connectors?
A wire-to-board (WTB) connector connects a cable assembly to a PCB-mounted header. A wire-to-wire (WTW) connector connects two cable assemblies directly to each other without a PCB. Most connector series offer both WTB and WTW variants (e.g., JST SM is WTW; JST XH is WTB). Some series are exclusively WTB (JST SH, GH) or WTW (JST PA, JST RCY). See our Wire-to-Board Connector Types guide for a complete framework.
Which Keszoox connector has the highest current rating?
The Molex Mini-Fit Jr. 4.2mm has the highest current rating in the Keszoox catalog at 13A per contact. The next highest is the JST VH 3.96mm at 10A per contact, followed by the Molex Micro-Fit 3.0 at 5A per contact. For applications requiring more than 13A, use a dedicated power connector outside the standard crimp connector families.
Summary
Keszoox supplies pre-crimped connector cable assemblies across 28 connector series from JST, Molex, DuPont, and Yeonho — covering pitches from 1.0mm to 4.2mm and current ratings from 1A to 13A per contact. All products use factory-crimped terminals, UL-rated wire, and are RoHS compliant.
Use the individual series guides linked throughout this page for complete specifications, part numbers, PCB footprint data, crimping instructions, and application guidance for each connector series. For identification help, start with How to Identify JST Connectors or How to Measure Connector Pitch.
🛒 Shop Keszoox Connector Kits · JST Assorted Kit · Molex Kit · DuPont 2.54mm Kit · HY2.0 Kit · SMH250 Kit