Keszoox
Toyota 90980-12790 6-Pin Reversing Radar & Rear Camera Connector — OEM Wiring Harness Plug
Toyota 90980-12790 6-Pin Reversing Radar & Rear Camera Connector OEM Wiring Harness Plug
Couldn't load pickup availability
Toyota 90980-12790 — 6-Pin Reversing Radar & Rear View Camera Wiring Connector
Part Number: 90980-12790
OEM Manufacturer: Toyota / Yazaki
The Toyota part number 90980-12790 identifies a 6-pin wiring connector used in Toyota's reversing radar (parking sensor) and rear view camera wiring harnesses. As factory-fitted parking sensors and reversing cameras have become standard equipment across Toyota's lineup — from the Corolla and Camry to the RAV4, Prius, and Hilux — this connector has become one of the most frequently replaced harness components in Toyota service and repair. Damage typically occurs during rear bumper removal for parking sensor installation or replacement, tow bar fitting, or accident repair. This OEM-specification replacement connector restores the factory wiring connection without cutting or splicing the harness.
Technical Specifications
- Part Number: 90980-12790
- OEM Cross-Reference: Toyota / Yazaki specification
- Pin Count: 6-pin
- Application: Reversing radar (PDC) sensor harness / rear view camera wiring connector
- Housing Material: PA66 — heat-stabilized, UV-resistant
- Terminal Material: Copper alloy, tin-plated
- Sealing: Sealed variant (individual wire seals) — suitable for underbumper/exterior locations
- Operating Temperature: -40°C to +120°C
- Voltage Rating: 12V DC
- Wire Gauge: 0.3–1.0 mm² (AWG 22–18) — signal-level wiring
- Locking: Positive-latch retention tab
Vehicle Compatibility
The 90980-12790 connector is used across a wide range of Toyota and Lexus models equipped with factory parking sensors and/or reversing cameras:
- Toyota Camry (XV50/XV70) — rear PDC sensor harness connector
- Toyota Corolla (E160/E210) — reversing camera and parking sensor wiring plug
- Toyota RAV4 (XA40/XA50) — rear bumper PDC harness connector
- Toyota Prius (XW30/XW50) — rear camera wiring connector
- Toyota Hilux (AN120/AN130) — reversing sensor harness plug (factory-fit and aftermarket)
- Toyota Land Cruiser Prado (J150) — rear PDC and camera harness connector
- Toyota Fortuner (AN150/AN160) — rear bumper sensor wiring plug
- Toyota Yaris / Vios — reversing camera harness connector on higher trim levels
- Lexus IS / RX / NX — rear PDC sensor harness connectors on shared Toyota platforms
Why This Connector Gets Damaged
The 90980-12790 sits in the rear bumper wiring harness — one of the most frequently disturbed areas of any vehicle. Rear bumper removal for parking sensor installation, tow bar fitting, accident repair, or bumper repainting is a routine workshop operation, and the connector is often damaged in the process: the locking tab breaks when the connector is pulled rather than released, or the housing cracks when the bumper is removed without fully disconnecting the harness. In markets where aftermarket parking sensor kits are popular — particularly Southeast Asia, the Middle East, and Australia — this connector is a high-volume replacement part for auto electricians and accessory installers.
Global Market & Regional Notes
Toyota's dominance in global markets means the 90980-12790 is in active demand across virtually every region where vehicles are serviced. Key markets include Japan, Australia, New Zealand, Southeast Asia (Thailand, Indonesia, Malaysia, Philippines, Vietnam), the Middle East (UAE, Saudi Arabia, Kuwait, Oman, Qatar), Africa (South Africa, Kenya, Nigeria), and Latin America (Brazil, Chile, Colombia, Argentina). In Thailand — Toyota's largest production hub outside Japan — this connector is widely available through Toyota dealers and aftermarket suppliers. In Australia and New Zealand, it is a standard stock item for Toyota specialists and 4WD accessory workshops.
Installation Notes
- Disconnect the vehicle battery before working on parking sensor or camera wiring
- Use a terminal extraction pick to remove pins — do not pull on the wire
- Inspect wire seals before re-use; replace if cracked
- Confirm pin orientation against the vehicle's wiring diagram — PDC sensor connectors are polarity-sensitive
- Apply dielectric grease to terminals in underbumper locations exposed to road spray
Package Contents
- 1 × 90980-12790 6-Pin Connector Housing
- Terminals and wire seals included (confirm at checkout)
Frequently purchased alongside: rear bumper PDC sensor sets, reversing camera modules, and tow bar wiring harness kits. Contact us for bundle pricing.
